Відео

Swap to a sport grill, don’t forget the sport grill bracket

No review after using? Is there a follow up video?

Just got the Primeweld 180 and love it the only I guess you could say complaint I have is when I adjust the wire speed it goes up by 2 or 3 . Say I want to weld at 235 and I'm at 233 it shot up too 236 . Does yours do that or is it just me or should I contact Primeweld about it ?

The problem is that this thing is so high the way it is without jacking it up, I couldn't use it because my toyota camry 2020 is very low

If you didn't need to sand your bed I'd love these

Next time, leave the copyright infringed music out and just talk

I did this! Guess what, my start stop is working on my 2020 glad

Thank you for this. Everywhere else says to take the dash off.

What you are not calculating is the fuel quality. Even the same station with the same fuel ….the fuel will degrade and you will get different results. Fresh fuel is better than 2 week old fuel and 2 week old fuel is better than 30 day old fuel.

I done this now for 6-7 years on a Chevy Express work van, and have used many products. The Duplicolor goes on well, but tends to fade in the sun. I've used that for many years, and the past couple something has changed and it definitely fades. I live in the Northeast, so typically not quite as hot as some

Is it possible for an s03 to work on 3rd gens?

Hey man, how you copin with the chips 😂😂 ive had the same model for 5mths, i just deal with it when finished just get the shop vac or broom i use the dewalt dw7260 folding stand one word, awesome Cant believe you got no comments!! I also had to fit a soft start module to mine because of high inrush current! But i love mine🎉 Cheers from the 🇬🇧

I bought most of these product and I’ve seen absolutely no improvement in mpg nothing. I think it expensive snake oil.

Plasma cutter 😂

Good video Chad, By any chance invite you to do a product review, We specifically produce LEDs for auto. We just emailed for an inquiry.

why don't you tell me how long it takes to recharge?? 30 hours!! Gbx 155 !!

Damn buddy I'm sure glad you put this up. Because I've been out there looking for a while.

That was pretty smooth what you did at 11:12 with the front direct band...lol 🤣🤣🤣

Herculiner- more durable than the others too.

I have this problem right now I deleted the auxiliary battery I connected the positive with the positive in main battery but the auto start stop sign still shown What you did to remove the sign fron dashboard Thanks

I do not see any problem… u are comparing apples with pies ☺️ it is built to last and will not brake…

WHERES YA DAGGUM SAFETY GOGGLE HOSS YULL BE PULLIN THE GRINDER CLIBBINS WIFF A MAGNET GOBBLESS

I Love Harbor Freight. Heres My 69" Box and My Set Up. ALL Harbor Freight. ua-cam.com/video/ztLypf_Tg7A/v-deo.htmlsi=aVJCaGt0At9cXlQA

I ground down the tv valve before watching this video and I don’t want manual. Will it be fine or do I need to buy a new one

just out of curiosity, when you put those lift blocks in did it push the axle forward some? I would imagine so because putting them above the factory blocks sort of angles the axle pushing it in further than when the added blocks would be below. sorry I'm having a hard time explaining. hope you understand 😂😂

What i need to know is how do you get it mated back on the main case ..i had trouble getting everything lined up ....i need a video ...

In my opinion, Continental and Dayco belts are better.

When is the upgrade

So, having looked at other projects and learning from them? I would go with the gen 2 sport Grill.

Dodge truck bodys benefit from being covered in oil. Helps keep it from rusting out.

How do you change the reverse light bulb if it goes bad?

Have you seen the new Fireball Dragon wagon? It looks a bit more heavy duty then this.

The friction reducer specifically says not to be used with stiction eliminator or any other additive right on the bottle. Why is it ok to use their oil that already has friction modifier in it with stiction eliminator?

Valve seals at the same time?

I have a non-tuned transmission with the holes drilled and channel plate hole plugged but it's for a 5 check ball setup, open slot in separator plate. My transmission is a 7 check ball. Will it run this way or do I need to leave 2 out. I have the white solenoid pack. Thanks.

Thank you for that tdc verification trick

Awsome content.

That’s pretty good mileage for 35s, towing, and I’m assuming it’s lifted a little bit?

We we love the GB150 , here in Australia they do the GB150 12v / 3000amos not like yours here thats a 4000amp . we have successfully jump started a toyota 200 series Landcrusier V8 (Australian released one again) . we have moved from projecta jump packs and chargers now we have the GB70 12v/2000a and now the GB150 12.3000a . also we gave the G15000 battery charger too. all these are all used for our fleet vetches

There are plenty of good brands of affordable wrenches out there without stooping to the Icon hype or to Shittsburg

I’m thinking about doing this to my gladiator but idk if I should go with the knee speakers lol

Good video! Helps a lot

How’s it working today 3 years later

Fasten a tube (opening at bottom - just off work surface to grinder) connected to a vac system (small hose works better), it should collect most of debris. ---- small shop vac hose extension, heated up about half the length (6"), pressed it into an oval shape and flaired the opening. If had a 3D printer could probably cast a better system of dust pick up. Enjoy your toy.

On the passenger side of the tie rod they have it crimped do yourself a favor and run a bead around where the 2 pieces meet it will get sloppy at that crimp and you will definitely feel it in the wheel.

Way too fast there bud.. but thanks

Can you ground directly to the table? Or does the coating prevent that.

Took mine off and it did not have that piston, just bought a new one and it doesn't have that piston...is it necessary?

No pulse 30% duty cycle on 220V for one thousand dollars?? bye Chad.

Chad I have a silver eagle 2760kw. I changed the hydraulic oil and now my left side has no power. When I jacked up the rear wheels the left side runs like a champ. But under a load it barely attempts to respond. Not sure if I have an air lock or if the pump was damaged trying to run it. Not sure how to figure out what is going on. I don’t have any leakage. Did you have to purge/bleed your hydraulic system after reinstalling? TIA